History Of Fanfare Shoe Stores

note booklet

Material: gray cardboard


-bookbinder bookbinding glue-sized canvas


paper-scissors-paper block

book corners
Glue-All

Here's how: Cut

The gray boxes on these dimensions to right:

Tip: There Please measure before the block, as there are various sizes. I added the dimension of 9 x 9 cm. Do you have a different level, then you need only 2 mm more for the cardboard blanks.

2 x 9.2, cm x 9.2 cm x 1.8 cm
1 x 9.2 cm



The Bookbinders lines on these measures to cut right:

1 x 7cm
"x 13.5 1 x 7 cm x 9 cm

alternative to the lines you could also use Tone on tone paper.

The bigger piece of cloth and bookbinding glue brush and replace the gray cardboard parts. Only the small piece to raise the center of the linen and then the older ones at the top and bottom with about 4 mm apart on the canvas. The pages turn inwards and tighten the folded seam.

Apply Now, the small piece of linen with glue.


The reference paper on the following dimensions to cut right:

2 x 14cm x 12 cm
2 x 9 cm × 9 cm
The reference paper back spread with glue and stick with a little distance from the folded seam, cut the corners and the excess paper to the inside fold and glue. The other side to work the same way.



The 2 small paper cuts Brush the back with glue and attach to the inside of the lid.


cut down from the paper pad is now 1.8 cm, thinly glued to the side of the block all the adhesive and align the center applied to the narrow middle section, and allow to dry. The book corners and attach decorations to your taste.

Pink Panther Gym Music

Small Ferrerotäschchen

Material:

- firmer
paper - Ruler
-
pencil - scissors
- Double-sided tape
- Band
- Ferreo kiss



Here's how:

The paper in the dimensions of 13.5 x 11 cm trimming. Measure from the narrow side at the edge of each 2 cm and draw a fold line, turning the sheet once and measure cm from the wider side respectively from the edge (both sides) of 5.5 and also draw the fold lines.




the fold lines to bend while pressing down on the ground inside the paper, the back ensteht a small rebate. This then makes it 4 times.


. Now stick to the top of the innengeknickte corners, the corners with double sided tape.





2 strips of 3 x 7 cm rightly cut and fold in the middle of the long side.



Both sides of inside with double sided tape and stick it on the top edge of the bag.




. Each punch 2 holes in the strip to fill the Tasch, and pull a ribbon through the holes ... ... ... ... ... .. done.

ornaments can be attached to your taste.

Do Yankee Candle Tarts Work In Scentsy Warmers

basic guide-3 D motifs make

Material:

• 3D Archery
• Abstandspads / silicone
• Scissors


Here's how:

A 3D-motif consists of several layers, which are glued to each other in three dimensions.
These layers are the so-called step-by-Step-arms already specified by the designer. First of all
cut parts of the subject.


The back - up to the plate - with Abstandspads provided.

Tip: It does not work much on the edge, because the pads can be seen later on the side.

alternative to the already finished buying pads or foam tape can be a foam rubber plate or thick cardboard on both sides with double sided tape and cut to fit.

Now, the protective film is removed from the adhesive pads and initially set the bottom layer to the base plate.

It can be used identical or slightly offset.

shall proceed with all the layers, the parts are getting smaller toward the top.

Who does not want to work with adhesive pads can also use silicone.

This applied selectively to the back of the motives and put the sheets over each other.

The disadvantage of this method is the long waiting time, which is caused by the drying of the silicone.

Tip: To contribute to have the motives especially plastic and cover the adhesive pad side, the images before applying the adhesive pads bent around with scissors.

Another form of 3D-arms consists of several bases of the same motif.

This is up to you which items He would like to stress is there and how many layers the subject.


This in turn cut the base plate.

The other layers the subject cut accordingly.

It cut away to the foreground towards more and more details.

The layers as usual with silicone adhesive pads or put together.

The so-made designs can now be applied to cards.

Tip: You might want the 3D images also emphasize with mica or 3-D paint.

Cylindrical Trash Bags

basic instructions - Tiffany

Material:

• Glass
• Glass Nugget
• Submission 2x
• waterproof pen
• glass cutter
• Glass breaking pliers
• Glass Grinding
• Copper foil
• soldering iron
• soldering fluid
• Solder
• Patina
• Film
• Scissors
• Copper wire
• silver wire
• Brush •
old towel


Here's how:

The Tiffany template required 2x: one comes in a clear plastic folder, and the other copies on cardboard and cut out. On the original paint on an arrow that shows should run in what direction the grain of the glass. The cut-out templates on the right side of the glass insert and record the outlines. cut

With the glass cutter on the line drawn along and break the glass with the glass breaking pliers.

The glass grinder to grind the exact fit the template. dry rub

the glass with an old cloth around the edges and wrap the edges with copper foil.

The entire glass parts are put back on the template, and soldered together.


the Copper wire wound tightly and turn up apart to solder the copper wire to the wings. Cut off small pieces of silver wire and turn to the sensors. This solder on the head.


rinse the whole butterfly, then rubbed with a patina and flush the whole thing again.

The butterfly can be placed ... be


... or put in a copper rod and used as flower plugs:


Tip: Spray
The final Tiffany part after the full completion with Pronto furniture spray and a soft cloth blank rub .............. the protects the solder oxidize before.

Przybycin Donata Knurów

Small Häkelblümchen

Material:

-crochet thread for needle size 1.5-2-
crochet hook No. 1.5 to 2
squeeze


Flower 1

Find it:

hit seven stitches and close to a ring.
first series - 15 single crochet in the ring
work second Series - 1 rod and double rod respectively into a scam to work, crochet two stitches, insert into the first chain stitch and pull the thread through both loops, a double rod and a rod in a Stitch work, a crochet ... repeat ... ... ... .. all other 4 x.
diameter: 3.5 cm


Flower 2

Find it:

hit seven stitches and close to a circle.
first series - 15 single crochet in the ring work.
second series - a stick and a double rods in a mesh work, repeating a Stick, crochet, all other 4 x.

diameter about 2 cm




Flower 3

Here's how:


hit six stitches and close to a circle.
first series - in the circle 12 sticks work.
second series - a single crochet, 3 chain stitches and one stitch leave and 2 in the crochet crochet a single crochet. As long repeat is closed to the series.
third series - In the crochet crochet a single crochet, 6 rods in the 3 stitches, work a slip stitch, repeat until the line is closed.

diameter about 3.7 cm